Projekti

Amendment 1 - Compression and mechanical connectors for power cables - Part 1-1: Test methods and requirements for compression and mechanical connectors for power cables for rated voltages up to 1 kV (U_m = 1,2 kV) tested on non-insulated conductors

20.99   Prednacrt standarda prihvata se kao nacrt standarda

Amendment 1 - Compression and mechanical connectors for power cables - Part 1-2: Test methods and requirements for insulation piercing connectors for power cables for rated voltages up to 1 kV (U_m = 1,2 kV) tested on insulated conductors

20.99   Prednacrt standarda prihvata se kao nacrt standarda

Amendment 1 - Compression and mechanical connectors for power cables - Part 1-3: Test methods and requirements for compression and mechanical connectors for power cables for rated voltages above 1 kV (U_m = 1,2 kV) up to 30 kV (U_m = 36 kV) tested on non-insulated conductors

20.99   Prednacrt standarda prihvata se kao nacrt standarda

Nuclear instrumentation - Portable gamma radiation meters and spectrometers used for prospecting - Definitions, requirements and calibration

40.00   Dopunjavanje i evidentiranje podataka o nacrtu standarda

Determination of long-term radiation ageing in polymers - Part 1: Techniques for monitoring diffusion-limited oxidation

20.99   Prednacrt standarda prihvata se kao nacrt standarda

Materials for printed boards and other interconnecting structures - Part 2-54: Reinforced base materials clad and unclad - Halogenated modified or unmodified resin system, woven E-glass laminate sheets of defined dissipation factor (less than 0,005 at 10 GHz) and flammability (vertical burning test), copper-clad for high speed applications

40.99   Nacrt standarda prihvata se kao definitivni tekst nacrta standarda

Materials for printed boards and other interconnecting structures - Part 2-55: Reinforced base materials clad and unclad - Non-halogenated modified or unmodified resin system, woven E-glass laminate sheets of defined dissipation factor (less than 0,005 at 10 GHz) and flammability (vertical burning test), copper-clad for high speed applications

30.99   Nacrt komisije standarda odobrava se za javnu raspravu

Materials for printed boards and other interconnecting structures - Part 2-56: Reinforced base materials clad and unclad – Non-halogenated epoxide modified bismaleimide/triazine with filler woven glass laminate sheets of low thermal expansion and flammability (vertical burning test), copper-clad for IC substrate

20.99   Prednacrt standarda prihvata se kao nacrt standarda

Nuclear power plants - Instrumentation and control systems important to safety - Detection of leakage in coolant systems

50.99   Definitivni tekst nacrta standarda odobren za objavljivanje

Electrical insulating materials and systems - Part 2: DC voltage endurance evaluation

30.20   Početak izjašnjavanja o nacrtu komisije standarda

Amendment 1 - Fibre-optic communication subsystem test procedures - Part 4-2: Installed cabling plant - Single-mode attenuation and optical return loss measurements

40.00   Dopunjavanje i evidentiranje podataka o nacrtu standarda

Overhead lines - Requirements and tests for fittings

50.99   Definitivni tekst nacrta standarda odobren za objavljivanje

Industrial-process control - Safety of analyser houses

40.60   Završetak javne rasprave

Optical amplifiers - Test methods - Part 11-1: Polarization mode dispersion parameter - Jones matrix eigenanalysis (JME)

40.00   Dopunjavanje i evidentiranje podataka o nacrtu standarda

Optical amplifiers - Test methods - Part 3-2: Noise figure parameters - Electrical spectrum analyzer method

50.00   Evidentiranje podataka o definitivnom tekstu nacrta standarda

Insulating liquids - Determination of the partial discharge inception voltage (PDIV) - Test procedure

20.99   Prednacrt standarda prihvata se kao nacrt standarda

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-19: Tests - Damp heat (steady state)

30.99   Nacrt komisije standarda odobrava se za javnu raspravu

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-2: Tests - Mating durability

60.00   Standard u postupku objavljivanja